Goto Section: 73.160 | 73.183 | Table of Contents
FCC 73.182
Revised as of
Goto Year:1996 |
1998
Sec. 73.182 Engineering standards of allocation.
(a) Sections 73.21 to 73.37, inclusive, govern allocation of
facilities in the AM broadcast band 535-1705 kHz. Sec. 73.21 establishes
three classes of channels in this band, namely, clear, regional and
local. The classes and power of AM broadcast stations which will be
assigned to the various channels are set forth in Sec. 73.21. The
classifications of the AM broadcast stations are as follows:
(1) Class A stations operate on clear channels with powers no less
than 10kW nor greater than 50 kW. These stations are designed to render
primary and secondary service over an extended area, with their primary
services areas protected from objectionable interference from other
stations on the same and adjacent channels. Their secondary service
areas are protected from objectionable interference from co-channel
stations. For purposes of protection, Class A stations may be divided
into two groups, those located in any of the contiguous 48 States and
those located in Alaska in accordance with Sec. 73.25.
(i) The mainland U.S. Class A stations are those assigned to the
channels allocated by Sec. 73.25. The power of these stations shall be
50 kW. The Class A stations in this group are afforded protection as
follows:
(A) Daytime. To the 0.1 mV/m groundwave contour from stations on the
same channel, and to the 0.5 mV/m groundwave contour from stations on
adjacent channels.
(B) Nighttime. To the 0.5 mV/m-50% skywave contour from stations on
the same channels.
(ii) Class A stations in Alaska operate on the channels allocated by
Sec. 73.25 with a minimum power of 10 kW, a maximum power of 50 kW, and
an antenna efficiency of 282 mV/m/kW at 1 kilometer. Stations operating
on these channels in Alaska which have not been designated as Class A
stations in response to licensee request will continue to be considered
as Class B stations. During daytime hours a Class A station in Alaska is
protected to the 100 V/m groundwave contour from co-channel
stations. During nighttime hours, a Class A station in Alaska is
protected to the 100 V/m-50 percent skywave contour from co-
channel stations. The 0.5 mV/m groundwave contour is protected both
daytime and nighttime from stations on adjacent channels.
[[Page 47]]
Note: In the Report and Order in MM Docket No. 83-807, the
Commission designated 15 stations operating on U.S. clear channels as
Alaskan Class A stations. Eleven of these stations already have Alaskan
Class A facilities and are to be protected accordingly. Permanent
designation of the other four stations as Alaskan Class A is conditioned
on their constructing minimum Alaskan Class A facilities no later than
December 31, 1989. Until that date or until such facilities are
obtained, these four stations shall be temporarily designated as Alaskan
Class A stations, and calculations involving these stations should be
based on existing facilities but with an assumed power of 10 kW.
Thereafter, these stations are to be protected based on their actual
Alaskan Class A facilities. If any of these stations does not obtain
Alaskan Class A facilities in the period specified, it is to be
protected as a Class B station based on its actual facilities. These
four stations may increase power to 10 kW without regard to the impact
on co-channel Class B stations. However, power increases by these
stations above 10 kW (or by existing Alaskan Class A stations beyond
their current power level) are subject to applicable protection
requirements for co-channel Class B stations. Other stations not on the
original list but which meet applicable requirements may obtain Alaskan
Class A status by seeking such designation from the Commission. If a
power increase or other change in facilities by a station not on the
original list is required to obtain minimum Alaskan Class A facilities,
any such application shall meet the interference protection requirements
applicable to an Alaskan Class A proposal on the channel.
(2) Class B stations are stations which operate on clear and
regional channels with powers not less than 0.25 kW nor more than 50 kW.
These stations render primary service only, the area of which depends on
their geographical location, power, and frequency. It is recommended
that Class B stations be located so that the interference received from
other stations will not limit the service area to a groundwave contour
value greater than 2.0 mV/m nighttime and to the 0.5 mV/m groundwave
contour daytime, which are the values for the mutual protection between
this class of stations and other stations of the same class.
Note: See Secs. 73.21(b)(1) and 73.26(b) concerning power
restrictions and classifications relative to Class B, Class C, and Class
D stations in Alaska, Hawaii, Puerto Rico and the U.S. Virgin Islands.
Stations in the above-named places that are reclassified from Class C to
Class B stations under Sec. 73.26(b) shall not be authorized to increase
power to levels that would increase the nighttime interference-free
limit of co-channel Class C stations in the conterminous United States.
(3) Class C stations operate on local channels, normally rendering
primary service to a community and the suburban or rural areas
immediately contiguous thereto, with powers not less than 0.25 kW, nor
more than 1 kW, except as provided in Sec. 73.21(c)(1). Such stations
are normally protected to the daytime 0.5 mV/m contour. On local
channels the separation required for the daytime protection shall also
determine the nighttime separation. Where directional antennas are
employed daytime by Class C stations operating with more than 0.25 kW
power, the separations required shall in no case be less than those
necessary to afford protection, assuming nondirectional operation with
0.25 kW. In no case will 0.25 kW or greater nighttime power be
authorized to a station unable to operate nondirectionally with a power
of 0.25 kW during daytime hours. The actual nighttime limitation will be
calculated. For nighttime protection purposes, Class C stations in the
48 contiguous United States may assume that stations in Alaska, Hawaii,
Puerto Rico, and the U.S. Virgin Islands operating on 1230, 1240, 1340,
1400, 1450, and 1490 kHz are Class C stations.
(4) Class D stations operate on clear and regional channels with
daytime powers of not less than 0.25 kW (or equivalent RMS field of 141
mV/m at one kilometer if less than 0.25 kW) and not more than 50 kW.
Class D stations that have previously received nighttime authority
operate with powers of less than 0.25 kW (or equivalent RMS fields of
less than 141 mV/m at one kilometer) are not required to provide
nighttime coverage in accordance with Sec. 73.24(j) and are not
protected from interference during nighttime hours. Such nighttime
authority is permitted on the basis of full nighttime protection being
afforded to all Class A and Class B stations.
(b) When a station is already limited by interference from other
stations to
[[Page 48]]
a contour value greater than that normally protected for its class, the
individual received limits shall be the established standard for such
station with respect to interference from each other station.
(c) The four classes of AM broadcast stations have in general three
types of service areas, i.e., primary, secondary and intermittent. (See
Sec. 73.14 for the definitions of primary, secondary, and intermittent
service areas.) Class A stations render service to all three areas.
Class B stations render service to a primary area but the secondary and
intermittent service areas may be materially limited or destroyed due to
interference from other stations, depending on the station assignments
involved. Class C and Class D stations usually have only primary service
areas. Interference from other stations may limit intermittent service
areas and generally prevents any secondary service to those stations
which operate at night. Complete intermittent service may still be
obtained in many cases depending on the station assignments involved.
(d) The groundwave signal strength required to render primary
service is 2 mV/m for communities with populations of 2,500 or more and
0.5 mV/m for communities with populations of less than 2,500. See
Sec. 73.184 for curves showing distance to various groundwave field
strength contours for different frequencies and ground conductivities,
and also see Sec. 73.183, ``Groundwave signals.''
(e) A Class C station may be authorized to operate with a
directional antenna during daytime hours providing the power is at least
0.25 kW. In computing the degrees of protection which such antenna will
afford, the radiation produced by the directional antenna system will be
assumed to be no less, in any direction, than that which would result
from non-directional operation using a single element of the directional
array, with 0.25 kW.
(f) All classes of broadcast stations have primary service areas
subject to limitation by fading and noise, and interference from other
stations to the contours set out for each class of station.
(g) Secondary service is provided during nighttime hours in areas
where the skywave field strength, 50% or more of the time, is 0.5 mV/m
or greater (0.1 mV/m in Alaska). Satisfactory secondary service to
cities is not considered possible unless the field strength of the
skywave signal approaches or exceeds the value of the groundwave field
strength that is required for primary service. Secondary service is
subject to some interference and extensive fading whereas the primary
service area of a station is subject to no objectionable interference or
fading. Only Class A stations are assigned on the basis of rendering
secondary service.
Note: Standards have not been established for objectionable fading
because of the relationship to receiver characteristics. Selective
fading causes audio distortion and signal strength reduction below the
noise level, objectionable characteristics inherent in many modern
receivers. The AVC circuits in the better designed receivers generally
maintain the audio output at a sufficiently constant level to permit
satisfactory reception during most fading conditions.
(h) Intermittent service is rendered by the groundwave and begins at
the outer boundary of the primary service area and extends to a distance
where the signal strength decreases to a value that is too low to
provide any service. This may be as low as a few V/m in certain
areas and as high as several millivolts per meter in other areas of high
noise level, interference from other stations, or objectionable fading
at night. The intermittent service area may vary widely from day to
night and generally varies over shorter intervals of time. Only Class A
stations are protected from interference from other stations to the
intermittent service area.
(i) Broadcast stations are licensed to operate unlimited time,
limited time, daytime, share time, and specified hours. (See
Secs. 73.1710, 73.1725, 73.1720, 73.1715, and 73.1730.) Applications for
new stations shall specify unlimited time operation only.
(j) Section 73.24 sets out the general requirements for modifying
the facilities of a licensed station and for establishing a new station.
Sections 73.24(b) and 73.37 include interference related
[[Page 49]]
provisions that be considered in connection with an application to
modify the facilities of an existing station or to establish a new
station. Section 73.30 describes the procedural steps required to
receive an authorization to operate in the 1605-1705 kHz band.
(k) Objectionable nighttime interference from a broadcast station
occurs when, at a specified field strength contour with respect to the
desired station, the field strength of an undesired station (co-channel
or first adjacent channel, after application of proper protection ratio)
exceeds for 10% or more of the time the values set forth in these
standards. The value derived from the root-sum-square of all
interference contributions represents the extent of a station's
interference-free coverage.
(1) With respect to the root-sum-square (RSS) values of interfering
field strengths referred to in this section, calculation of nighttime
interference-free service is accomplished by considering the signals on
the three channels of concern (co- and first adjacencies) in order of
decreasing magnitude, adding the squares of the values and extracting
the square root of the sum, excluding those signals which are less than
50% of the RSS values of the higher signals already included.
(2) With respect to the root-sum-square values of interfering field
strengths referred to in this section, calculation of nighttime
interference for non-coverage purposes is accomplished by considering
the signals on the three channels of concern (co- and first adjacencies)
in order of decreasing magnitude, adding the squares of the values and
extracting the square root of the sum, excluding those signals which are
less than 25% of the RSS values of the higher signals already included.
(3) With respect to the root-sum-square values of interfering field
strengths referred to in this section, calculation is accomplished by
considering the signals on the three channels of concern (co- and first
adjacencies) in order of decreasing magnitude, adding the squares of the
values and extracting the square root of the sum. The 0% exclusion
method applies only to the determination of an improvement factor value
for evaluating a station's eligibility for migration to the band 1605-
1705 kHz.
(4) The RSS value will not be considered to be increased when a new
interfering signal is added which is less than the appropriate exclusion
percentage as applied to the RSS value of the interference from existing
stations, and which at the same time is not greater than the smallest
signal included in the RSS value of interference from existing stations.
(5) It is recognized that application of the above ``50% exclusion''
method (or any exclusion method using a per cent value greater than
zero) of calculating the RSS interference may result in some cases in
anomalies wherein the addition of a new interfering signal or the
increase in value of an existing interfering signal will cause the
exclusion of a previously included signal and may cause a decrease in
the calculated RSS value of interference. In order to provide the
Commission with more realistic information regarding gains and losses in
service (as a basis for determination of the relative merits of a
proposed operation) the following alternate method for calculating the
proposed RSS values of interference will be employed wherever
applicable.
(6) In the cases where it is proposed to add a new interfering
signal which is not less than 50% (or 25%, depending on which study is
being performed) of the RSS value of interference from existing stations
or which is greater that the smallest signal already included to obtain
this RSS value, the RSS limitation after addition of the new signal
shall be calculated without excluding any signal previously included.
Similarly, in cases where it is proposed to increase the value of one of
the existing interfering signals which has been included in the RSS
value, the RSS limitation after the increase shall be calculated without
excluding the interference from any source previously included.
(7) If the new or increased signal proposed in such cases is
ultimately authorized, the RSS values of interference to other stations
affected will thereafter be calculated by the ``50% exclusion'' (or 25%
exclusion, depending on which study is being performed)
[[Page 50]]
method without regard to this alternate method of calculation.
(8) Examples of RSS interference calculations:
(i) Existing interferences:
Station No. 1--1.00 mV/m.
Station No. 2--0.60 mV/m.
Station No. 3--0.59 mV/m.
Station No. 4--0.58 mV/m.
The RSS value from Nos. 1, 2 and 3 is 1.31 mV/m; therefore interference
from No. 4 is excluded for it is less than 50% of 1.31 mV/m.
(ii) Station A receives interferences from:
Station No. 1--1.00 mV/m.
Station No. 2--0.60 mV/m.
Station No. 3--0.59 mV/m.
It is proposed to add a new limitation, 0.68 mV/m. This is more than 50%
of 1.31 mV/m, the RSS value from Nos. 1, 2 and 3. The RSS value of
Station No. 1 and of the proposed station would be 1.21 m/Vm which is
more than twice as large as the limitation from Station No. 2 or No. 3.
However, under the above provision the new signal and the three existing
interferences are nevertheless calculated for purposes of comparative
studies, resulting in an RSS value of 1.47 mV/m. However, if the
proposed station is ultimately authorized, only No. 1 and the new signal
are included in all subsequent calculations for the reason that Nos. 2
and 3 are less than 50% of 1.21 mV/m, the RSS value of the new signal
and No. 1.
(iii) Station A receives interferences from:
Station No. 1--1.00 mV/m.
Station No. 2--0.60 mV/m.
Station No. 3--0.59 mV/m.
No. 1 proposes to increase the limitation it imposes on Station A to
1.21 mV/m. Although the limitations from stations Nos. 2 and 3 are less
than 50% of the 1.21 mV/m limitation, under the above provision they are
nevertheless included for comparative studies, and the RSS limitation is
calculated to be 1.47 mV/m. However, if the increase proposed by Station
No. 1 is authorized, the RSS value then calculated is 1.21 mV/m because
Stations Nos. 2 and 3 are excluded in view of the fact that the
limitations they impose are less than 50% of 1.21 mV/m.
Note: The principles demonstrated in the previous examples for the
calculation of the 50% exclusion method also apply to calculations using
the 25% exclusion method after appropriate adjustment.
(l) Objectionable nighttime interference from a station shall be
considered to exist to a station when, at the field strength contour
specified in paragraph (q) of this section with respect to the class to
which the station belongs, the field strength of an interfering station
operating on the same channel or on a first adjacent channel after
signal adjustment using the proper protection ratio, exceeds for 10% or
more of the time the value of the permissible interfering signal set
forth opposite such class in paragraph (q) of this section.
(m) For the purpose of estimating the coverage and the interfering
effects of stations in the absence of field strength measurements, use
shall be made of Figure 8 of Sec. 73.190, which describes the estimated
effective field (for 1 kW power input) of simple vertical
omnidirectional antennas of various heights with ground systems having
at least 120 quarter-wavelength radials. Certain approximations, based
on the curve or other appropriate theory, may be made when other than
such antennas and ground systems are employed, but in any event the
effective field to be employed shall not be less than the following:
------------------------------------------------------------------------
Class of station Effective field (at 1 km)
------------------------------------------------------------------------
All Class A (except Alaskan)............... 362 mV/m.
Class A (Alaskan), B and D................. 282 mV/m.
Class C.................................... 241 mV/m.
------------------------------------------------------------------------
Note (1): When a directional antenna is employed, the radiated signal of
a broadcasting station will vary in strength in different directions,
possibly being greater than the above values in certain directions and
less in other directions depending upon the design and adjustment of
the directional antenna system. To determine the interference in any
direction, the measured or calculated radiated field (unattenuated
field strength at 1 kilometer from the array) must be used in
conjunction with the appropriate propagation curves. (See Sec. 73.185
for further discussion and solution of a typical directional antenna
case.)
Note (2): For Class B stations in Alaska, Hawaii, Puerto Rico and the
U.S. Virgin Islands, 241 mV/m shall be used.
(n) The existence or absence of objectionable groundwave
interference from stations on the same or adjacent channels shall be
determined by actual measurements made in accordance with the method
described in Sec. 73.186, or in the absence of such measurements, by
reference to the propagation curves of Sec. 73.184. The existence or
absence of objectionable interference due to skywave propagation shall
be determined by reference to Formula 2 in Sec. 73.190.
(o) Computation of Skywave Field Strength Values:
[[Page 51]]
(1) Fifty Percent Skywave Field Strength Values (Clear Channel). In
computing the fifty percent skywave field strength values of a Class A
clear channel station, use shall be made of Formula 1 of Sec. 73.190,
entitled ``Skywave Field Strength'' for 50 percent of the time.
(2) Ten Percent Skywave Field Strength Values. In computing the 10%
skywave field strength for stations on a single signal or an RSS basis,
Formula 2 in Sec. 73.190 shall be used.
(3) Determination of Angles of Departure. In calculating skywave
field strength for stations on all channels, the pertinent vertical
angle shall be determined by use of the formula in Sec. 73.190(d).
(p) The distance to any specified groundwave field strength contour
for any frequency may be determined from the appropriate curves in
Sec. 73.184 entitled ``Ground Wave Field Strength vs. Distance.''
(q) Normally protected service contours and permissible interference
signals for broadcast stations are as follows (for Class A stations, see
also paragraph (a) of this section):
A.................. Clear............. SC 100 SC 500 50% SW SC 5
SC 25
AC 500 AC 500 GW AC 250
AC 250
A (Alaskan)........ ......do.......... SC 100 SC 100 50% SW SC 5
SC 5
AC 500 AC 500 GW AC 250
AC 250
B.................. Clear............. 500 2000 \2\ 25
25
Regional.......... ................ ................... AC 250
250
C.................. Local............. 500 No presc.\4\ SC25
Not presc.
D.................. Clear............. 500 Not presc SC 25
Not presc.
Regional.......... ................ ................... AC 250
...............
------------------------------------------------------------------------------------------------
----------------
\1\ When a station is already limited by interference from other stations to a contour of higher
value than that
normally protected for its class, this higher value contour shall be the established protectio
n standard for
such station. Changes proposed by Class A and B stations shall be required to comply with the
following
restrictions. Those interferers that contribute to another station's RSS using the 50% exclusi
on method are
required to either reduce their contributions to that RSS by 10%, or to a level at which their
contributions
no longer enter into the 50% RSS value, whichever is the lesser amount of reduction. Those int
erferers that
contribute to a station's RSS using the 25% exclusion method but do not contribute to that sta
tion's RSS using
the 50% exclusion method may make changes not to exceed their present contribution. Interferer
s not included
in a station's RSS using the 25% exclusion method are permitted to increase radiation as long
as the 25%
exclusion threshold is not equalled or exceeded. In no case will a reduction be required that
would result in
a contributing value that is below the pertinent value specified in the table. This note does
not apply to
Class C stations; or to the protection of Class A stations which are normally protected on a s
ingle signal,
non-RSS basis.
\2\ Groundwave.
\3\ Skywave field strength for 10 percent or more of the time.
\4\ During nighttime hours, Class C stations in the contiguous 48 States may treat all Class B s
tations assigned
to 1230, 1240, 1340, 1400, 1450 and 1490 kHz in Alaska, Hawaii, Puerto Rico and the U.S. Virgi
n Islands as if
they were Class C stations.
Note: SC=Same channel; AC=Adjacent channel; SW=Skywave; GW=Groundwave
(r) The following table of logarithmic expressions is to be used as
required for determining the minimum permissible ratio of the field
strength of a desired to an undesired signal. This table shall be used
in conjunction with the protected contours specified in paragraph (q) of
this section.
------------------------------------------------------------------------------------------------
----------------
Desired Groundwave to:
Frequency separation of desired to -------------------------------------------------- Desire
d 50% Skywave to
undesired signals (kHz) Undesired groundwave Undesired 10% Skywave Undesi
red 10% Skywave
(dB) (dB)
(dB)
------------------------------------------------------------------------------------------------
----------------
0.................................... 26 26
26
10................................... 6 6
not presc.
------------------------------------------------------------------------------------------------
----------------
(s) Two stations, one with a frequency twice of the other, should
not be assigned in the same groundwave service area unless special
precautions are taken to avoid interference from the second harmonic of
the station operating on the lower frequency. Additionally, in selecting
a frequency, consideration should be given to the fact that occasionally
the frequency assignment of two stations in the same area may bear such
a relation to the intermediate frequency of some broadcast
[[Page 52]]
receivers as to cause ``image'' interference, However, since this can
usually be rectified by readjustment of the intermediate frequency of
such receivers, the Commission, in general, will not take this kind of
interference into consideration when authorizing stations.
(t) The groundwave service of two stations operating with
synchronized carriers and broadcasting identical programs will be
subject to some distortion in areas where the signals from the two
stations are of comparable strength. For the purpose of estimating
coverage of such stations, areas in which the signal ratio is between
1:2 and 2:1 will not be considered as receiving satisfactory service.
Note: Two stations are considered to be operated synchronously when
the carriers are maintained within 0.2 Hz of each other and they
transmit identical program s.
[ 56 FR 64862 , Dec. 12, 1991; 57 FR 43290 , Sept. 18, 1992, as amended at
58 FR 27950 , May 12, 1993]
Goto Section: 73.160 | 73.183
Goto Year: 1996 |
1998
CiteFind - See documents on FCC website that
cite this rule
Want to support this service?
Thanks!
Report errors in
this rule. Since these rules are converted to HTML by machine, it's possible errors have been made. Please
help us improve these rules by clicking the Report FCC Rule Errors link to report an error.
hallikainen.com
Helping make public information public