Goto Section: 2.1511 | 2.1515 | Table of Contents

FCC 2.1513
Revised as of October 1, 2009
Goto Year:2008 | 2010
  §  2.1513   Measurements of modulation characteristics.

   (a) Set-up. Test of modulation characteristics are to be performed in
   an RF shielded room.

   Step (1) Place the EPIRB directly on a metal ground plane, such as the
   shielded room floor.

   Step (2) Place a suitable receiving antenna at a convenient distance
   from the EPIRB and connect it to the input of the spectrum analyzer or
   receiver to observe the radiated signal from the EPIRB.

   Step (3) Set the spectrum analyzer or receiver controls as follows:

   I.F. bandwidth: 300 kHz minimum

   Video filter: OFF or as wide as possible

   Amplitude scale: Linear

   Frequency: 121.5 MHz

   Scan width: 0 Hz

   Step (4) Connect the detected output of the spectrum analyzer or
   receiver to the input of the storage oscilloscope.

   Step (5) Set the oscilloscope controls as necessary to allow the
   demodulated waveform to be viewed. The input signal is to be DC
   coupled.

   (b) Measurement of Audio Frequencies.

   Step (1) Activate the EPIRB.

   Step (2) Trigger the oscilloscope and store at least one complete cycle
   of the audio waveform.

   Step (3) Measure the period (T) of the waveform. The period is the time
   difference between the half voltage points at the beginning and end of
   one complete cycle of the waveform. See Figure 2.

   Step (4) Calculate the frequency (F), where:

   F=1/T.

   Step (5) Repeat Steps 2 through 4 until the highest and lowest audio
   frequencies are found.

   Note: The lowest and highest frequencies may occur several cycles
   before or after the transition from low to high frequency.)

   Step (6) Determine the audio frequency range (F[range]), where:

   F[range]=F[high]−F[low]

   Step (7) Record instrument settings and the lowest and highest audio
   frequencies. Record the audio frequency range in Hertz.

   Step (8) Repeat Steps 1–7, above, for 243 MHz.

   (c) Modulation factor.

   Step (1) Activate the EPIRB.

   Step (2) Trigger the oscilloscope and store at least one complete cycle
   of the audio waveform. The input signal is to be DC coupled or
   erroneous results will be obtained.

   Step (3) Measure the maximum voltage (V[max]), and the minimum voltage
   (V[min]) for the cycle. The modulation factor (M) is calculated from
   the following formula:
   [MATH:  :MATH]

   See Figure 2.

   Step (4) Repeat Steps 2 and 3 until the lowest modulation factor is
   found.

   Step (5) Record instrument settings and the lowest modulation factor,
   expressed as a ratio between 0 and 1.

   Step (6) Repeat the above measurements for 243 MHz.

   (d) Modulation duty cycle.

   Step (1) Activate the EPIRB.

   Step (2) Trigger the oscilloscope and store at least one complete cycle
   of the audio waveform.

   Step (3) Measure the period (T) of the waveform. The period is the time
   difference between the half voltage points at the beginning and end of
   one cycle of the waveform. See Figure 2.

   Step (4) Measure the pulse width (t[p]) of the waveform. The pulse
   width is the time difference between the half voltage points on the
   rising and falling portions of the waveform. See Figure 2.

   Step (5) Calculate the duty cycle (D) as follows:
   [MATH:  :MATH]

   Step (6) Repeat Steps 2 through 5 a sufficient number of times to
   determine the highest and lowest duty cycles.

   Step (7) Record instrument settings and the highest and lowest duty
   cycles in percent.

   Step (8) Repeat Steps 1–7 for 243 MHz.

   (e) Sweep repetition rate.

   Step (1) Connect a speaker to the detected output of the spectrum
   analyzer or receiver so the audio frequencies are audible.
   Alternatively, an FM radio tuned to 108 MHz placed in the vicinity of
   the EPIRB may be used.

   Step (2) Activate the EPIRB.

   Step (3) Time the number of audio sweeps (N) for a one minute interval.

   Step (4) Calculate the audio sweep rate (R) using R=N/60.

   Step (5) Record instrument settings and the sweep repetition rate in
   Hertz.


Goto Section: 2.1511 | 2.1515

Goto Year: 2008 | 2010
CiteFind - See documents on FCC website that cite this rule

Want to support this service?
Thanks!

Report errors in this rule. Since these rules are converted to HTML by machine, it's possible errors have been made. Please help us improve these rules by clicking the Report FCC Rule Errors link to report an error.
hallikainen.com
Helping make public information public