Goto Section: 25.131 | 25.133 | Table of Contents

FCC 25.132
Revised as of October 1, 2018
Goto Year:2017 | 2019
  § 25.132   Verification of earth station antenna performance.

   (a)(1) Except as provided in paragraph (a)(2) of this section,
   applications for transmitting earth stations in the FSS, including
   feeder-link stations, must include a certification that the applicant
   has reviewed the results of a series of radiation pattern tests
   performed by the antenna manufacturer on representative equipment in
   representative configurations, and the test results demonstrate that
   the equipment meets relevant off-axis gain standards in § 25.209,
   measured in accordance with paragraph (b)(1) of this section.
   Applicants and licensees must be prepared to submit the radiation
   pattern measurements to the Commission on request.

   (2) Applicants that specify off-axis EIRP density pursuant to
   § 25.115(g)(1) are exempt from the certification requirement in
   paragraph (a)(1) of this section.

   (b)(1) For purposes of paragraph (a)(1) of this section and
   § 25.115(g)(1), the following measurements on a production antenna
   performed on calibrated antenna range must be made at the top and
   bottom of each frequency band assigned for uplink transmission:

   (i)(A) Co-polarized gain in the azimuth plane must be measured across a
   range extending to 180° on each side of the main-lobe axis, and the
   measurements must be represented in two plots: one across the entire
   angular range of ±180° from the main-lobe axis and the other across
   ±10° from the main-lobe axis.

   (B) Co-polarized gain must be measured from 0° to 30° from beam peak in
   the elevation plane.

   (ii) Cross-polarization gain must be measured across a range of plus
   and minus 7° from beam peak in the azimuth and elevation planes.

   (iii) Main beam gain.

   (iv) For antennas with asymmetric apertures or beams, where the minor
   axis of the antenna beam (major axis of the antenna aperture) will not
   always be aligned parallel to the plane tangent to the GSO arc, the
   measurements in paragraphs (b)(1)(i) through (iii) of this section must
   be made over the angular ranges specified in paragraphs (b)(1)(i)(A)
   and (B) of this section in two orthogonal planes, with the antenna
   oriented at the maximum skew angle at which it will operate.

   (2) The relevant envelope specified in § 25.209 must be superimposed on
   each measured pattern.

   (c) The tests specified in paragraph (b) of this section are normally
   performed at the manufacturer's facility; but for those antennas that
   are very large and only assembled on-site, on-site measurements may be
   used for product qualification data. If on-site data is to be used for
   qualification, the test frequencies and number of patterns should
   follow, where possible, the recommendations in paragraph (b) of this
   section, and the test data is to be submitted in the same manner as
   described in paragraph (a) of this section.

   (d) For each new or modified transmitting antenna over 3 meters in
   diameter, except antennas subject to measurement under § 25.138(d), the
   following on-site verification measurements must be completed at one
   frequency on an available transponder in each frequency band of
   interest and submitted to the Commission.

   (1) Co-polarized patterns in the elevation plane, plus and minus 7
   degrees, in the transmit band.

   (2) Co-polarized patterns in the azimuth and elevation planes, plus and
   minus 7 degrees, in the receive band.

   (3) System cross-polarization discrimination on-axis. The FCC envelope
   specified in § 25.209 shall be superimposed on each pattern. The
   transmit patterns are to be measured with the aid of a co-operating
   earth station in coordination with the satellite system control center
   under the provisions of § 25.272.

   (e) Certification that the tests required by paragraph (c) of this
   section have been satisfactorily performed shall be provided to the
   Commission in notification that construction of the facilities has been
   completed as required by § 25.133.

   (f) Antennas less than 3 meters in diameter and antennas on simple
   (manual) drive mounts that are operated at a fixed site are exempt from
   the requirements of paragraphs (c) and (d) of this section provided
   that a detailed technical showing is made that confirms proper
   installation, pointing procedures, and polarization alignment and
   manufacturing quality control. These showing must also include a plan
   for periodic testing and field installation procedures and precautions.

   (g) Records of the results of the tests required by this section must
   be maintained at the antenna site or the earth station operator's
   control center and be available for inspection.

   [ 58 FR 13419 , Mar. 11, 1993, as amended at  69 FR 5710 , Feb. 6, 2004;  70 FR 32253 , June 2, 2005;  72 FR 50028 , Aug. 29, 2007;  74 FR 47102 , Sept.
   15, 2009;  74 FR 57098 , Nov. 4, 2009;  78 FR 14926 , Mar. 8, 2013;  79 FR 8318 , Feb. 12, 2014;  81 FR 55330 , Aug. 18, 2016]

   return arrow Back to Top


Goto Section: 25.131 | 25.133

Goto Year: 2017 | 2019
CiteFind - See documents on FCC website that cite this rule

Want to support this service?
Thanks!

Report errors in this rule. Since these rules are converted to HTML by machine, it's possible errors have been made. Please help us improve these rules by clicking the Report FCC Rule Errors link to report an error.
hallikainen.com
Helping make public information public